Factory floor loading in Klang: what kN/m² means and how to check before machines, racking or a mezzanine
Ms Teh Seok Hoon, PEA 4006. Updated
Floor loading is the load a floor was designed to carry on each square metre. Engineers write it in kN/m²; listings in Klang usually give tonnes per m², and 1 t/m² is about 9.8 kN/m². Units on Ms Teh's list state 1 to 5 t/m², and size and estate predict the figure better than the terrace, semi-D or detached label. Check it on the approved structural plans, which Selangor's building by-laws require to mark each floor's design load.
Key takeaways
- 1 kN/m² is roughly 102 kg on every square metre; 3 t/m² is about 29 kN/m² and 5 t/m² about 49 kN/m².
- On her list, small cluster, link and semi-D units in Puncak Alam state 1 t/m², semi-Ds in KIIP Kapar, Kapar Bestari, Bukit Raja and Meru 3 t/m², and detached units anything from 1 to 5 t/m².
- Selangor's Uniform Building By-Laws make the structural plans show the imposed load each floor was designed for, and floors that may take forklifts need special provision.
- For machines, the by-laws require impact and vibration to be designed for, with an increase of at least 20%, plus the loads while equipment is installed or moved.
- A mezzanine is a structural addition: MBDK asks for structural plans with calculations, and added floor area over 92 m² goes to its technical development meeting.
- 1 t/m² in kN/m²
- about 9.8 kN/m² (multiply tonnes by 9.81)
- Floor loading stated on her units
- 1 to 5 t/m² (about 10 to 49 kN/m²)
- Machine loads (Selangor by-law 68)
- increase of at least 20% for impact and vibration
- MBDK alteration referral
- added floor over 92 m² goes to the technical development meeting
What kN per square metre means, and how it compares with t/m²
A floor loading figure is a load per unit of floor area. Structural engineers use kilonewtons per square metre (kN/m², the same as kPa). One kilonewton is about the weight of 102 kg, so a floor designed for 5 kN/m² is meant to take about 510 kg spread over every square metre. Factory listings in Klang and Port Klang, including Ms Teh's, usually state the figure in tonnes per square metre instead. Multiply tonnes by 9.81 to get kilonewtons: 1.5 t/m² is about 15 kN/m², 3 t/m² about 29 kN/m² and 5 t/m² about 49 kN/m². Older drawings sometimes use pounds per square foot; 1 kN/m² is about 20.9 lb/sq ft.
The figure describes an evenly spread load. Real loads are not even: a rack stands on small base plates, a machine on its feet, a forklift on its wheels. Selangor's Uniform Building By-Laws deal with this directly. By-law 54 says that where the actual imposed load will exceed the calculated one, the actual load must be used, and that plant or machinery producing exceptional dynamic effects must be designed for a larger equivalent static load. So a listing that says 3 t/m² tells you the slab was meant for an even 3 t/m², not that a 3 tonne machine on four small feet is safe anywhere on it.
FactoryHub's floor loading calculator turns a rack bay or a machine into tonnes per square metre, which is a quick way to see which units are worth a viewing. The point loads still need an engineer, as the sections below explain.
Typical figures for terrace, semi-D and detached factories on her list
There is no fixed floor loading for a building type. The figure comes from the owner or the original drawings, and on Ms Teh's list the estate and the size of the unit predict it better than whether it is a terrace, semi-detached or detached factory. These are the figures as stated on her current units, in t/m² with kN/m² in brackets:
Two lessons follow. A semi-D can carry more than a detached factory, so filter by the figure, not the type. And a figure of 1 t/m² is not a defect: it suits assembly, light storage and offices, but not five levels of one tonne pallets or a heavy press. FactoryHub's Kapar industrial area page shows the floor loading of units across Kapar where owners state it.
- Terrace and link factories: the terrace units she has in Pandamaran do not state a figure; a 4,700 sq ft link factory in Eco Business Park V, Puncak Alam, states 1 t/m² (about 10 kN/m²).
- Small units in Puncak Alam: cluster factories of about 3,000 to 4,200 sq ft and semi-Ds of about 7,900 to 8,200 sq ft in Eco Business Park V and Bandar Puncak Alam state 1 t/m²; the larger semi-Ds of about 32,000 sq ft in Eco Business Park V state 3 t/m² (about 29 kN/m²).
- Semi-Ds in Kapar, Bukit Raja and Meru: units from 4,235 to 22,556 sq ft in KIIP Kapar, Kapar Bestari, Bukit Raja and Meru that state a figure all give 3 t/m², for example a 15,260 sq ft semi-D in KIIP Kapar.
- Semi-Ds near Northport: a 35,179 sq ft unit in Perdana Industrial Park states 2 t/m², while a 7,200 sq ft semi-D in Kampung Kastam states 5 t/m² (about 49 kN/m²).
- Detached factories and warehouses: anything from 1 to 5 t/m². Detached units of 22,462 and 39,341 sq ft in Kapar Bestari and Sungai Kapar Indah, and warehouses of about 55,000 to 57,000 sq ft around Northport, state 1.5 t/m²; units of about 225,000 to 255,000 sq ft at Westport state 5 t/m².
What a 1, 3 or 5 t/m² floor can carry
What is a 1 t/m² factory floor good for?
Light work. 1 t/m² is about 10 kN/m², the figure stated by the cluster factories, link factories and smaller semi-Ds in Eco Business Park V and Bandar Puncak Alam on Ms Teh's list. It suits assembly, packing, workshops and goods stored on the floor or low shelving. High racking, heavy stock or machines on small feet need an engineer's check against the structural plans before you sign.
What machines can stand on a 3 t/m² floor?
3 t/m² is about 29 kN/m², the figure most semi-Ds in Kapar, Bukit Raja and Meru on her list state. It is an evenly spread load, so a machine is judged by the weight under each foot, not its total. Selangor's by-law 54 says the actual load must be used where it is higher, and machines with heavy vibration are designed for a larger equivalent load. Give the maker's foundation drawing to an engineer.
Is a 5 t/m² factory floor enough for heavy industry?
For heavy storage, usually; for heavy machines, not by itself. 5 t/m², about 49 kN/m², is stated by the large Westport warehouses on her list and suits tall racking and heavy stock. Presses, furnaces or machines with impact loads are a point load question: by-law 68 requires installed machinery to be designed for at least 20% more imposed load, and many need their own foundation or plinth.
What Selangor's building by-laws require
Factories in Klang, Port Klang, Kapar, Meru and Puncak Alam are built under the Selangor Uniform Building By-Laws 1986, made under the Street, Drainage and Building Act 1974. Since the 2012 amendment (Sel. P.U. 142/2012), by-law 59 says all imposed floor loads are calculated to the Malaysian Standard MS EN 1991-1-1; the amendment replaced the earlier wording of that by-law and deleted the Fourth Schedule of tables. A factory approved before then was designed under the earlier rules, which is one more reason to read its drawings instead of assuming.
Three rules matter to an occupier. By-law 16 requires the structural plans to be clearly marked with the imposed loads for which each floor, or each part of it, has been designed: that marking is the figure to look for. By-law 60 says that where forklifts or other mechanical stacking machines may be used, the floor design must make special provision for them. By-law 55 applies the loading rules not only to new buildings but also to structural alterations and additions, and to existing buildings on a change of use. Turning a light assembly floor into dense storage is a change the floor has to be checked for.
Structural plans are signed by a qualified person, which the by-laws define as a Professional Architect, Professional Engineer or building draughtsman registered under the relevant law. For a question about what a floor can carry, the person to ask is a Professional Engineer.
Heavy machines: point loads, vibration and moving them in
Machines are where a stated t/m² figure misleads most. By-law 68 of the Selangor by-laws says concentrated imposed loads, including impact and vibration from installed machinery, must be considered in the design, and the increase in imposed loads must be at least 20% or the minimum in MS EN 1991-1-1, whichever is higher. The same by-law asks for provision for concentrated equipment loads while the equipment is being installed or moved for servicing and repair. Under by-law 69, crane gantry girders are designed for vibration, shocks from slipping slings, acceleration and braking, and the impact of wheel loads.
In practice, before you sign for a unit:
For racking, the floor check works the same way; her guide on pallet racking in a Klang warehouse works through bay loads, clear height and Bomba.
- Get the machine maker's foundation or installation drawing: the total weight, the load under each foot, the footprint and any dynamic load.
- Mark where each machine will sit, so the engineer checks those exact spots and not an average.
- Plan the route in: the forklift, pallet jack or crane that moves the machine across the floor adds its own load.
- Give all of this, with the unit's structural plans, to a Professional Engineer and ask in writing whether the slab takes it or the machine needs its own plinth.
- If building works for the machine go to MBDK, its alteration plan checklist asks for a copy of the JKKP (DOSH) approval or certificate for mechanical equipment where relevant.
Mezzanine floors: what they must carry and what the council asks for
The Selangor by-laws define a mezzanine floor as any floor interposed between the main floors of a building, including any platform or landing more than 2.5 metres wide. It is a floor in its own right, so it needs a design load for its own use: an office, a store for light cartons and a pick floor for heavy stock are different cases. A mezzanine also puts its weight on the ground slab through its columns, which is a point load on the floor below.
For a unit under Majlis Bandaraya Diraja Klang (MBDK), adding one is an alteration. MBDK's checklist for alteration plans, in force since April 2024, asks for a copy of the structural plans with their calculations. A building draughtsman may only submit additions of up to 300 m², on buildings of no more than two storeys, with reinforced concrete or steel frame spans of no more than 2.5 m; anything larger goes through an architect or engineer. Additions of more than 92 m² (about 1,000 sq ft) of floor are referred to the council's Mesyuarat Teknikal Pembangunan for full approval. MBDK's building department states a decision on non-residential alteration and addition applications within seven days, and it takes enforcement action against alterations built without its written permission.
Puncak Alam's estates fall under Majlis Perbandaran Kuala Selangor (MPKS), as her Puncak Alam page sets out. The MPKS form for additions and alterations to houses, shops and factories asks for reinforcement plans and calculations with Form A and the current practising permit of an engineer registered with the Board of Engineers (LJM). It warns that works may not start before the plans are approved, that starting early can cost ten times the plan processing fee, and that failing to comply can bring, on conviction under section 70(13) of Act 133, a fine of up to RM50,000 plus RM1,000 for each day the offence continues. Bukit Raja Selatan sits under Shah Alam's council rather than MBDK; her guide on which council covers Bukit Raja explains the split.
The risk is real. In November 2018 part of a mezzanine floor at a furniture factory in Batu Pahat collapsed while three workers were stacking goods on it, killing a 64-year-old worker below, Malay Mail reported from Bernama; DOSH Johor said legal action would follow if the employer had breached the Occupational Safety and Health Act. New buildings plan the load from the start: in November 2026 Binastra won a RM303.8 million contract for an automated storage and retrieval warehouse with a mezzanine floor in Bandar Bukit Raja, Klang, covering the piling as well as the buildings, The Star reported.
How to check a unit's floor loading before you sign
The figure on a listing is where the check starts. Before you commit to a unit for heavy use, work through these steps:
Ms Teh can help you shortlist units in Kapar, Meru, Northport, Pulau Indah and Puncak Alam by their stated floor loading and ask the owners for their drawings before the first viewing.
- Write down your loads: rack bays, machines with the weight per foot, stock stacked on the floor, the forklift and any mezzanine you plan.
- Ask the owner for the approved building plans and the structural plans; under by-law 16 the structural plans should mark the design imposed load of each floor or part of it.
- Ask for the Certificate of Completion and Compliance (CCC) or, for an older building, the Certificate of Fitness (CF). MBDK's building department receives Form F for the CCC, and it has a form for a copy of a CF that an owner can use for their own records.
- If there are no drawings, ask a Professional Engineer to assess the slab before you sign, and agree with the landlord who pays.
- Put the agreed floor loading and any approved changes, such as a mezzanine or machine plinths, into the tenancy agreement or the sale and purchase agreement.
Questions buyers and tenants ask
How many kilograms is 5 kN/m²?
About 510 kg on each square metre. One kN is roughly the weight of 102 kg, so multiply kN/m² by about 102 to get kg/m², or divide by 9.81 to get tonnes per square metre: 5 kN/m² is about 0.51 t/m², and 49 kN/m² is about 5 t/m².
Is 3 t/m² enough for a warehouse with forklifts and racking?
It can be for light pallets and low racking, but it depends on your bay loads, pallet weights and the forklift. Selangor's by-law 60 requires floors that may take forklifts to be designed with special provision for them, so ask whether this slab was, and have an engineer check the base plate loads.
Is Pelabuhan Utara the same as Northport, and what floor loading do units there state?
Yes, Pelabuhan Utara is the Malay name for Northport in Port Klang. On Ms Teh's list, warehouses of about 55,000 to 57,000 sq ft there state 1.5 t/m², units of 71,982, 95,334 and 132,969 sq ft state 3.5 t/m², a 131,731 sq ft warehouse in Perdana Industrial Park states 4 t/m² and a 189,000 sq ft unit in Bandar Sultan Suleiman states 5 t/m².
Do I need council approval to add a mezzanine to my factory in Klang?
Yes. In MBDK's area it is an alteration: MBDK's checklist asks for structural plans with calculations, larger additions must go through an architect or engineer, and added floor area over 92 m² is referred to its technical development meeting. In Puncak Alam, the MPKS form says works may not start before approval.
Where do I find the design floor loading of an older factory?
On its approved structural plans, which by-law 16 requires to mark the imposed load of each floor. Ask the owner for the set kept with the building. If no plans exist, ask a Professional Engineer to assess the slab before you sign, and treat any figure without drawings behind it as unconfirmed.
Can a factory floor be strengthened for a heavier machine?
An engineer may propose strengthening the slab or a separate foundation for the machine. Either is a structural alteration, which by-law 55 brings under the loading rules, and it needs the council's approval before work starts. Agree it with the landlord in writing first.
What approvals do I need to install large machinery in a Klang factory?
It depends on the machine and the building work. A new foundation, pit or slab strengthening is structural work for the council: MBDK's alteration plan checklist asks for Form A from your consultant, the contractor's CIDB registration, a title search, the building's CF and, where relevant, DOSH approval for the equipment and Bomba's letter. Lifting machinery, boilers and pressure vessels also need DOSH certificates; an ordinary CNC or press does not.
Units in these places
- Detached Factory/Warehouse for Rent in Kapar Bestari, 22,462 sq ft, 200A · RM 50,000 / month
- Industrial Land for Sale in Kapar, 2.34 acres · RM 8,658,005
- Semi-D Factory/Warehouse for Rent in Meru, 25,700 sq ft, Medium Industrial · RM 48,000 / month
- Detached Factory/Warehouse for Sale or Rent in Meru, 76,074 sq ft, 6000A · RM 35,797,000 or RM 167,363 / month
- Semi-D Factory/Warehouse for Sale or Rent in Kampung Kastam, 7,200 sq ft, 200A · RM 2,800,000 or RM 13,000 / month
- All listings
Updated
Sources
- KPKT (Jabatan Kerajaan Tempatan): Selangor Uniform Building By-Laws 1986, Sel. P.U. 26/1985, updated to Sel. P.U. 142/2012 (by-laws 16, 54, 55, 59, 60, 68, 69)
- MBDK: Jabatan Bangunan, functions and client charter (read Nov 2026)
- MBDK: Borang Senarai Semak Pelan Ubahsuai, MPK/BGN/BORANG-PS-1 (in force 1 Apr 2024)
- MBDK: Borang Permohonan Salinan Sijil Layak Menduduki (CF) (Apr 2024)
- MPKS: Borang Pelan Ubahsuaian dan Tambahan, rumah kediaman, kedai, kilang (JKB05, Oct 2025)
- Malay Mail (Bernama): Mezzanine floor collapses killing elderly worker in Batu Pahat (Nov 2018)
- The Star: Binastra bags RM303.8mil industrial warehouse contract in Klang (Nov 2026)
- The Star: Binastra's latest job win to bolster industrial edge (Nov 2026)
- FactoryHub: Floor loading calculator
- FactoryHub: Kapar industrial area (KIIP Kapar, Sungai Kapar Indah, Kapar Bestari)
Tell Ms Teh what you need
Send the size, power, ceiling height, budget and move-in date you need on WhatsApp, or call her directly.