Container truck access in Klang: road width, turning space, gate and loading bay size for 20 ft and 40 ft
Ms Teh Seok Hoon, PEA 4006. Updated
Plan for the whole truck, not the box. Malaysian rules cap a prime mover and semi-trailer at 16 m long and 2.6 m wide, and every vehicle must turn within a 12.5 m outer radius. At a Klang or Port Klang unit, check that the road and gate let it swing in, that the lot holds a 4 m by 18 m trailer bay plus 18.3 m to manoeuvre, and that every beam and canopy clears 4.5 m.
Key takeaways
- A prime mover with a 40 ft container may be up to 16 m long and 2.6 m wide; combinations over 16 m, up to 18 m, need the Minister's authorisation.
- PLANMalaysia sizes a trailer bay at 4 m by 18 m and adds 18.3 m to manoeuvre, 36.3 m in all, inside the lot.
- MBDK wants factory roads on a 12.2 m or 15.2 m reserve paved to full width; a dead end should end in a turning circle more than 30 m across.
- Selangor's building by-laws keep the fire engine access way at least 6 m wide with 4.5 m headroom and free of obstructions, so trailers cannot wait on it.
- MBDK tows heavy vehicles parked on main roads and in housing areas, so the truck that waits needs room inside your gate.
- Longest prime mover and semi-trailer
- 16 m (up to 18 m with authorisation)
- Widest vehicle
- 2.6 m (up to 3 m with authorisation)
- Turning circle every vehicle must meet
- Between 12.5 m and 5.3 m radius
- Trailer bay (PLANMalaysia GP011-A)
- 4 m x 18 m plus 18.3 m to manoeuvre
- Fire engine access way (Selangor UBBL)
- At least 6 m wide, 4.5 m headroom
The truck you are planning for
A 20 ft or 40 ft container reaches a factory in Kapar, Klang or Port Klang on a semi-trailer pulled by a prime mover, so the numbers that matter at the gate are the truck's, not the box's. The Motor Vehicles (Construction and Use) (Amendment) Rules 2024 set the maximum overall length of a prime mover with a semi-trailer at 16 m, and of the semi-trailer alone at 12.5 m. The Minister may authorise combinations of more than 16 m up to 18 m, and semi-trailers up to 13.8 m (Attorney General's Chambers, P.U. (A) 88/2024).
The same rules cap the overall width at 2.6 m, with authorisation possible up to 3 m, and allow an authorised overall height of up to 4.2 m. They also require every motor vehicle to be able to turn so that no part of it leaves the ring between two circles of 12.5 m and 5.3 m radius. Read that as the space a legal truck sweeps on a full turn: about 25 m across on the outside.
A 20 ft box is shorter, but the prime mover is the same and the trailer may not be shorter. Ask your haulier which trailer it sends for each container size and whether any of your cargo moves on authorised longer or wider combinations, then measure the unit for the longest truck that will come.
Estate roads and turning space
Factories in Kapar, Meru, Port Klang, Northport and Pulau Indah come under Majlis Bandaraya Diraja Klang (MBDK). Its checklist for road and drain plans, in force since 5 February 2024, sets how much of a road in front of or beside a factory must be paved: the full width on a 12.2 m (40 ft) or 15.2 m (50 ft) road reserve, 12.2 m on an 18.3 m (60 ft) reserve, 17.6 m (58 ft) on a 20.1 m (66 ft) reserve, and a dual carriageway with a median from 100 ft up. Side and back lanes 20 ft wide behind terrace factories must be one-way (MBDK).
Those are design figures for new plans. On an older estate road, measure what is really there: kerb to kerb at your gate and at the junction the truck turns in from, with the usual cars and lorries parked. If the only way to your loading door is a 20 ft back lane that MBDK makes one-way, test it with your haulier before you count on it for containers.
Dead ends are the trap. PLANMalaysia's parking guideline says trailer parking should avoid dead-end roads, and where one cannot be avoided it should be under 190 m long from the junction with a turning circle more than 30 m (100 ft) across (PLANMalaysia GP011-A). The older federal guideline for planning industrial areas explains why: a circle of that size lets a 14 m (45 ft) trailer turn 180 degrees by reversing (JPBD industrial planning guideline). At a unit at the end of a dead end without that circle, every container leaves by reversing out.
Gate, driveway, fire access and overhead clearance
The Ministry of Transport's guidebook on starting a warehousing business suggests two gates of at least 10 m each when they are apart, 6 m each when they sit side by side, or one 15 m main gate, with a 6 m ring road around the warehouse (Ministry of Transport). That is guidance for new warehouses, not law, but it shows the scale a container operation works at. Councils set limits on the driveway itself: Majlis Perbandaran Kuala Selangor (MPKS), the council for Puncak Alam, lists a factory driveway, with its steel grating over the roadside drain, at no more than 9,100 mm wide (MPKS).
Fire access sets a floor under all of this. Selangor's Uniform Building By-Laws, as amended in 2012, require a fire appliance access way at least 6 m wide along its whole length, able to carry a stationary 30 tonne fire appliance, with at least 4.5 m of overhead clearance, turning facilities on any dead end longer than 46 m, and no obstructions (Selangor UBBL amendment, Sel. P.U. 142/2012). MBDK's building plan checklist carries the 6 m fire access road as a plan condition and says a building of more than 7,000 m² must front a road or open space at least 12 m wide (MBDK).
For a tenant this has a practical side: the fire access way is not a trailer park. A container or trailer left on it blocks a route the by-law says must be kept clear, so the yard needs truck waiting space somewhere else.
Overhead, PLANMalaysia asks for at least 4.5 m of headroom in lorry areas on flat ground and 4.75 m on ramps, and its heavy vehicle terminal guideline asks for at least 14 ft (4.25 m) under a dock canopy. Check gate frames, canopies, cable trays, pipes and signboards, and ask your haulier for the laden height of the truck with your container type, standard or high cube. The route outside matters too: in October 2026 a trailer from the port carrying oversized cargo struck the underside of an overpass at Jalan Perbandaran in Klang and jammed the traffic (Sin Chew).
Loading bay size, apron depth and dock height
PLANMalaysia's parking guideline (GP011-A, 2018) gives the minimum bay for each lorry type: 3 m by 6 m for a small lorry, 4 m by 15 m for a large lorry and 4 m by 18 m for a trailer, where large lorries and trailers mean vehicles of 3 to 6 axles such as trailers, container lorries and prime movers. In front of the bay it adds manoeuvring space of 6 m, 15.3 m and 18.3 m, so a trailer needs 36.3 m of straight length in all. It suggests at least two loading spaces so trucks do not queue, and for a detached or semi-detached factory on a lot of more than one acre it asks for one loading space per 1,858 m² of gross floor area, at most 9 and at least 2, all inside the lot.
PLANMalaysia's heavy vehicle terminal guideline (GP026, 2012) shows how bay width trades against apron depth. For a 40 ft (12.2 m) truck, a 3.06 m bay needs a 14.0 m apron and a 4.25 m bay needs 11.9 m. For a 60 ft (18.3 m) truck, the same bays need 22.0 m and 18.3 m. Measure the apron from the dock edge, or from the outermost column or parked vehicle if something stands in the way (PLANMalaysia GP026). A 16 m prime mover and trailer falls between the 50 ft and 60 ft rows of that table, so the 60 ft row is the safe one to plan on.
Dock height: GP026 suggests 1.2 m to 1.32 m and the Ministry of Transport guidebook 1 m to 1.6 m, with dock levellers where the dock is raised. For inclined docks the guidebook asks for a dock at least 3.5 m wide and at least 20 m clear in front, or 25 m where there is no separate truck aisle.
Some units on her list show what this looks like in practice: a 189,000 sq ft warehouse in Bandar Sultan Suleiman near Northport has 20 loading bays, and a 60,711 sq ft warehouse in Pulau Indah has 22. The count is only a start: at a viewing, ask which bays are raised docks, which have levellers and how much apron each one has. Floor loading inside the door matters too; the factory floor loading guide explains how to read it.
How many loading bays, how wide a door, how many gates?
What is a loading bay, and how many does a factory need?
A loading bay is the space where a lorry parks to load or unload. PLANMalaysia's guideline sizes a trailer bay at 4 m by 18 m, suggests at least two bays so trucks do not queue, and for a detached or semi-D factory on a lot of more than one acre asks for one per 1,858 m² of floor area, between 2 and 9, all inside the lot. Port side warehouses on her list carry 20 or more.
What size roller shutter does a factory loading door need?
Size it to the truck, not a standard. No by-law sets a shutter size, but PLANMalaysia asks for at least 4.5 m of headroom in lorry areas on flat ground and 4.25 m under a dock canopy, and sizes a trailer bay 4 m wide. Ask your haulier for the laden height of a standard and a high cube container on its trailer, and check gate frames, canopies and cable trays on the way in.
How many gates or entrances does a factory need?
The Ministry of Transport's warehousing guidebook suggests two gates of at least 10 m each when they are apart, 6 m each side by side, or one 15 m main gate, with a 6 m ring road around the building. That is guidance, not law. Councils cap the driveway: MPKS, the Puncak Alam council, lists a factory driveway at no more than 9,100 mm wide.
Port Klang realities: waiting trucks, port hours and side loaders
In Klang, a truck that cannot get in has nowhere legal to wait. MBDK tows heavy vehicles left in housing areas and on main roads: from January to August 2025 it towed or seized 1,474 vehicles, 102 of them heavy vehicles, and a councillor told Sin Chew that a heavy vehicle parked illegally costs a RM1,000 fine plus RM3,000 for the crane and tow, a RM200 administration fee and RM100 a day in the council pound (Sin Chew). PLANMalaysia's guidelines point the same way: lorry and trailer parking should not be at the roadside next to buildings, and a factory's lorry bays belong inside its lot.
Port timing changes what the unit needs. A Ministry of Transport statement on the National Logistics Task Force in May 2025 said 70% of haulage at Port Klang ran in the 8 am to 8 pm peak, and approved a RM10 Terminal Access Charge on hauliers entering the port in those hours to fund off-peak incentives of RM15 for dual and RM7.50 for single movements (Ministry of Transport). That touches warehouses near Northport and those in Pulau Indah near Westports alike. Ask your haulier what applies today, and if you plan to receive containers at night, make sure the lease, the estate guard and the yard lighting allow it.
No raised dock? Some operators have the container set down on the ground with a side loader trailer. The Port Klang Authority said that from 1 July 2025 side loader trailers are disallowed for back-to-back laden import and export container movements, because the weight of the lifting gear cuts the payload; back-to-back haulage on standard skeletal trailers stays allowed within the permitted gross combination weight (The Edge). If your plan depends on a side loader, check with the haulier before you choose a unit without docks.
Parking container trucks, and the Northport hours
How many lorries or containers can a Klang factory park at once?
Count what fits inside the lot, because the road is not an option: MBDK tows heavy vehicles from roads and housing areas, and a councillor put the cost at a RM1,000 fine plus RM3,000 for the tow. Each trailer needs a 4 m by 18 m bay plus 18.3 m of manoeuvring space, 36.3 m of straight length in all. The 6 m fire access way must stay clear, so it does not count.
How much land do I need to park ten 40 ft container trucks?
For the bays alone, roughly 1,450 m², about 15,600 sq ft, using PLANMalaysia's trailer bay of 4 m by 18 m plus 18.3 m of manoeuvring space: ten bays side by side make a strip 40 m wide and 36.3 m deep. Add the building, the 6 m fire access way and the gates. A one acre detached lot with 60% site coverage leaves only about 17,400 sq ft open, so look at larger lots.
Is Pelabuhan Utara the same as Northport, and do port hours matter for my warehouse?
Yes, Pelabuhan Utara is the Malay name for Northport. Port hours matter because in May 2025 the National Logistics Task Force approved a RM10 charge on port entries from 8 am to 8 pm and incentives for off-peak moves, so a warehouse that can receive at night may suit importers who shift to off-peak. Check with your haulier how it is applied today.
What to measure at a viewing
Bring a measuring wheel or a laser meter, the plan of the unit and, if you can, your haulier. Then check:
Before you sign, ask the haulier to run one empty truck in and out. A trial run shows what a plan cannot.
- Road: kerb to kerb width at the gate and at the junction the truck turns in from, with the usual parked vehicles, and whether the road is a dead end with or without a turning circle.
- Gate: the clear opening between the gate posts, the splay at the kerb, and whether the gate leaf swings out into the road.
- Yard: the straight clear length in front of each bay (36.3 m for a trailer under GP011-A, or the GP026 apron for your bay width), the slab and drain covers the truck will cross, and room for a second truck to wait inside.
- Overhead: gate frames, canopies, cable trays, pipes and signboards against 4.5 m.
- Bays: how many are raised docks, their height against 1.2 m to 1.32 m, levellers, door width and height, and lighting for night work.
- Fire lane: where the 6 m fire access way runs, so that waiting trailers will not block it.
- Papers: the approved building and layout plans and the CCC, and in a semi-detached or shared site, whether the driveway is yours alone or shared.
Units in Kapar, Northport and Pulau Indah
Ms Teh Seok Hoon (PEA 4006, CID Realtors) can help you shortlist and view factories and warehouses in Kapar, Northport and Pulau Indah where a container truck can get in, turn and dock. For estate profiles, see FactoryHub's pages on the Bandar Sultan Suleiman industrial area and Pulau Indah Industrial Park.
Questions buyers and tenants ask
How long is a 40 footer lorry in Malaysia?
Under the Motor Vehicles (Construction and Use) (Amendment) Rules 2024, a prime mover with a semi-trailer may be up to 16 m long overall, and the semi-trailer alone up to 12.5 m. The Minister may authorise longer combinations up to 18 m. Width is capped at 2.6 m.
What is the standard loading bay size for a container trailer?
PLANMalaysia's parking guideline sets a minimum of 4 m by 18 m for a trailer bay, with 18.3 m of manoeuvring space in front, 36.3 m in total. Its heavy vehicle terminal guideline gives apron depths by bay width: for a 60 ft truck, 22.0 m in front of a 3.06 m bay or 18.3 m in front of a 4.25 m bay.
Can container trucks wait on the road outside my factory in Klang?
Not safely. MBDK tows heavy vehicles parked on main roads and in housing areas, and a councillor put the cost at a RM1,000 fine, RM3,000 for the tow, RM200 in fees and RM100 a day in the pound. Plan waiting space inside the gate, away from the fire access way.
My unit has no raised dock. Can the container be unloaded on the ground?
It can be, but agree the method with your haulier first. The Port Klang Authority disallowed side loader trailers for back-to-back laden import and export moves from 1 July 2025, because the lifting gear cuts the payload. Without a dock you also need firm, level ground beside the truck and room for the equipment you will use.
Does a 20 ft container need less space than a 40 ft one?
The box is shorter, but the space is set by the truck. A prime mover and semi-trailer may be up to 16 m long whatever it carries, and every vehicle must turn within a 12.5 m outer radius. Ask the haulier which trailer it sends for 20 ft boxes and measure for the longest truck that will come.
Which industrial areas in Klang can 40 ft container trucks get into?
Container trucks run daily in the port side estates of Pulau Indah, Westport and Northport's Bandar Sultan Suleiman. The harder cases are older terrace rows in Klang town, Meru and Kapar, where a 20 ft back lane that MBDK makes one-way, or a dead end without a turning circle of about 30 m, means the trailer cannot turn. Judge the road at your own gate and the junction before it, not the estate name, and test it with your haulier.
Units in these places
- Semi-D Factory/Warehouse for Sale or Rent in Kampung Kastam, 7,200 sq ft, 200A · RM 2,800,000 or RM 13,000 / month
- Detached Factory/Warehouse for Sale in Bandar Sultan Suleiman, 51,189 sq ft, 200A · RM 18,000,000
- Terrace Factory/Warehouse for Rent in Perigi Nanas, 2,949 sq ft · RM 4,500 / month
- Industrial Land for Rent in Pulau Indah, 0.45 acres · RM 6,000 / month
- Detached Factory/Warehouse for Rent in Kapar Bestari, 22,462 sq ft, 200A · RM 50,000 / month
- All listings
Updated
Sources
- Attorney General's Chambers: Motor Vehicles (Construction and Use) (Amendment) Rules 2024, P.U. (A) 88 (Mar 2024)
- PLANMalaysia: Garis Panduan Perancangan Tempat Letak Kenderaan GP011-A (2018)
- PLANMalaysia: Garis Panduan Perancangan Terminal Kenderaan Berat GP026 (Dec 2012)
- JPBD Semenanjung Malaysia: Garis Panduan Perancangan Kawasan Perindustrian, JPBD 12/97 (hosted by PLANMalaysia Johor)
- MBDK: Senarai Semak Permohonan Pelan Jalan dan Parit P2_04 (in force Feb 2024)
- MBDK: Senarai Semak Permohonan Pelan Bangunan P2_07 (in force Feb 2024)
- Selangor: Uniform Building By-Laws (Amendment) 2012, Sel. P.U. 142 (Dec 2012)
- Ministry of Transport (National Logistics Task Force): Guidebook to Starting Warehousing Business in Malaysia (May 2021)
- Ministry of Transport: National Logistics Task Force Meeting No. 1/2025 media release (May 2025)
- Majlis Perbandaran Kuala Selangor: Panduan (plan requirements, driveway widths)
- Sin Chew: 王城市厅:截至8月 充公拖走1474违例车 (Oct 2025)
- Sin Chew: 拖格罗里卡高架桥底 巴生哥打桥路今早大堵塞 (Oct 2026)
- The Edge: Port Klang Authority clarifies haulage overloading measures (May 2025)
Tell Ms Teh what you need
Send the size, power, ceiling height, budget and move-in date you need on WhatsApp, or call her directly.